基于STM32单片机和AD9850的智能DDS函数信号发生器

CSDN话题挑战赛第2期
参赛话题：学习笔记

1、整体设计

有一天，我在浏览CSDN时看到一篇关于 AD9850 的帖子。AD9850是一款可以产生1hz到40mhz左右正弦波的芯片。淘宝的产品经销商能够将芯片与提供 TTL 电平控制的小板配对，然后以令人难以置信的 60元（或更低！）的价格出售。

要控制 AD9850，您需要某种微控制器。无需过多详细说明，您需要向芯片发送一组串行或并行数据来设置频率。网上有很多帖子详细说明了如何做到这一点，所以我不会详细介绍。然而，很难找到一个好的 AD9850 引脚排列，所以你去吧。

2、硬件方案

GND = 地；Vss
CLK = 串行编程时钟
Latch = 串行编程锁存器（9850 上的 FQ_UD 引脚）
DATA = 串行编程 DATA（内部连接到 D7）
RST = 复位。保持连接到 GND
SQW = 方波输出（互补） 占空比可通过蓝色电位器调节。
SINA = 原始未滤波 AD9850 正弦输出
SINB = 70 MHz LPF 滤波 AD9850 输出。

对我来说，管理 AD9850 的最简单方法是使用 Arduino Uno。如果您不了解 Arduino 平台，您应该查看官方网站www.arduino.cc。我使用 Arduino 好多年了，我已经发现它是一个很棒的开发平台。如果你是一个业余爱好者……你真的不会出错。

这个项目正在进行中。您应该能够从 Arduino Sketch 中推断出所有项目的引脚，但如果您有任何问题，请联系我。我的原理图有点粗糙，因为我不倾向于经常创建它们，所以如果你发现任何不合适的东西，请告诉我！

由于有很多请求，我还为 IF（超外差）类型的接收器创建了一个版本。VFO 现在支持中频，并且可以切换 Arduino 上一个模拟输入的高/低电平。IF 可以是您想要的任何东西，可以是加法或减法。

DDS VFO 的输出电压随频率而变化，因此如果您需要它在宽范围 VFO 上输出恒定电平，您需要在缓冲器中设计一个 AGC（或排序）以提供恒定电平输出. 我已经看到一些带有简单运算放大器的出色设计，它们通过接入反馈电路来实现这一点。

同时这个方案它适用于 nano。注意：Arduino 的 D10 连接到 AD9850 的 DATA 引脚，而不是 D7。

连接后的硬件电路如下：

3、软件程序

arduino的程序如下：

#include 
#include 
#include 
 
//Setup some items
#define W_CLK 8   // Pin 8 - connect to AD9850 module word load clock pin (CLK)
#define FQ_UD 9   // Pin 9 - connect to freq update pin (FQ)
#define DATA 10   // Pin 10 - connect to serial data load pin (DATA)
#define RESET 11  // Pin 11 - connect to reset pin (RST) 
#define pulseHigh(pin) {digitalWrite(pin, HIGH); digitalWrite(pin, LOW); }
Rotary r = Rotary(2,3); // sets the pins the rotary encoder uses.  Must be interrupt pins.
LiquidCrystal lcd(12, 13, 7, 6, 5, 4); // I used an odd pin combination because I need pin 2 and 3 for the interrupts.
int_fast32_t rx=7000000; // Starting frequency of VFO
int_fast32_t rx2=1; // variable to hold the updated frequency
int_fast32_t increment = 100; // starting VFO update increment in HZ.
int buttonstate = 0;
String hertz = "100 Hz";
int  hertzPosition = 5;
byte ones,tens,hundreds,thousands,tenthousands,hundredthousands,millions ;  //Placeholders
String freq; // string to hold the frequency
int_fast32_t timepassed = millis(); // int to hold the arduino miilis since startup
int memstatus = 1;  // value to notify if memory is current or old. 0=old, 1=current.
 
int ForceFreq = 1;  // Change this to 0 after you upload and run a working sketch to activate the EEPROM memory.  YOU MUST PUT THIS BACK TO 0 AND UPLOAD THE SKETCH AGAIN AFTER STARTING FREQUENCY IS SET!
 
void setup() {
  Serial.begin(9600);
  Serial.println("Start...");
  pinMode(A0,INPUT); // Connect to a button that goes to GND on push
  digitalWrite(A0,HIGH);
  lcd.begin(16, 2);
  r.begin();
  PCICR |= (1 << PCIE2);
  PCMSK2 |= (1 << PCINT18) | (1 << PCINT19);
  sei();
  pinMode(FQ_UD, OUTPUT);
  pinMode(W_CLK, OUTPUT);
  pinMode(DATA, OUTPUT);
  pinMode(RESET, OUTPUT); 
  pulseHigh(RESET);
  pulseHigh(W_CLK);
  pulseHigh(FQ_UD);  // this pulse enables serial mode on the AD9850 - Datasheet page 12.
  Serial.println("DDS v1.0.0");
  lcd.clear();
  lcd.setCursor(hertzPosition,1);    
  lcd.print(hertz);
   // Load the stored frequency  
  if (ForceFreq == 0) {
    freq = String(EEPROM.read(0))+String(EEPROM.read(1))+String(EEPROM.read(2))+String(EEPROM.read(3))+String(EEPROM.read(4))+String(EEPROM.read(5))+String(EEPROM.read(6));
    rx = freq.toInt();  
    Serial.println(rx);
  }
  
}
 
 
void loop() {
  if (rx != rx2){    
        showFreq();
        sendFrequency(rx);
        rx2 = rx;
      }
      
  buttonstate = digitalRead(A0);
  if(buttonstate == LOW) {
        setincrement();        
    };
 
  // Write the frequency to memory if not stored and 20 seconds have passed since the last frequency change.
    if(memstatus == 0){   
      if(timepassed+20000 < millis()){
        storeMEM();
      }
    }   
}
 
 
ISR(PCINT2_vect) {
  unsigned char result = r.process();
  if (result) {    
    if (result == DIR_CW){rx=rx+increment;}
    else {rx=rx-increment;};       
      if (rx >=30000000){rx=rx2;}; // UPPER VFO LIMIT
      if (rx <=500000){rx=rx2;}; // LOWER VFO LIMIT
  }
}
 
 
 
// frequency calc from datasheet page 8 =  * /2^32
void sendFrequency(double frequency) {  
  int32_t freq = frequency * 4294967295/125000000;  // note 125 MHz clock on 9850.  You can make 'slight' tuning variations here by adjusting the clock frequency.
  for (int b=0; b<4; b++, freq>>=8) {
    tfr_byte(freq & 0xFF);
  }
  tfr_byte(0x000);   // Final control byte, all 0 for 9850 chip
  pulseHigh(FQ_UD);  // Done!  Should see output
}
// transfers a byte, a bit at a time, LSB first to the 9850 via serial DATA line
void tfr_byte(byte data)
{
  for (int i=0; i<8; i++, data>>=1) {
    digitalWrite(DATA, data & 0x01);
    pulseHigh(W_CLK);   //after each bit sent, CLK is pulsed high
  }
}
 
void setincrement(){
  if(increment == 1){increment = 10; hertz = "10 Hz"; hertzPosition=5;}
  else if(increment == 10){increment = 50; hertz = "50 Hz"; hertzPosition=5;}
  else if (increment == 50){increment = 100;  hertz = "100 Hz"; hertzPosition=4;}
  else if (increment == 100){increment = 500; hertz="500 Hz"; hertzPosition=4;}
  else if (increment == 500){increment = 1000; hertz="1 Khz"; hertzPosition=6;}
  else if (increment == 1000){increment = 2500; hertz="2.5 Khz"; hertzPosition=4;}
  else if (increment == 2500){increment = 5000; hertz="5 Khz"; hertzPosition=6;}
  else if (increment == 5000){increment = 10000; hertz="10 Khz"; hertzPosition=5;}
  else if (increment == 10000){increment = 100000; hertz="100 Khz"; hertzPosition=4;}
  else if (increment == 100000){increment = 1000000; hertz="1 Mhz"; hertzPosition=6;}  
  else{increment = 1; hertz = "1 Hz"; hertzPosition=5;};  
   lcd.setCursor(0,1);
   lcd.print("                ");
   lcd.setCursor(hertzPosition,1); 
   lcd.print(hertz); 
   delay(250); // Adjust this delay to speed up/slow down the button menu scroll speed.
};
 
void showFreq(){
    millions = int(rx/1000000);
    hundredthousands = ((rx/100000)%10);
    tenthousands = ((rx/10000)%10);
    thousands = ((rx/1000)%10);
    hundreds = ((rx/100)%10);
    tens = ((rx/10)%10);
    ones = ((rx/1)%10);
    lcd.setCursor(0,0);
    lcd.print("                ");
   if (millions > 9){lcd.setCursor(1,0);}
   else{lcd.setCursor(2,0);}
    lcd.print(millions);
    lcd.print(".");
    lcd.print(hundredthousands);
    lcd.print(tenthousands);
    lcd.print(thousands);
    lcd.print(".");
    lcd.print(hundreds);
    lcd.print(tens);
    lcd.print(ones);
    lcd.print(" Mhz  ");
    timepassed = millis();
    memstatus = 0; // Trigger memory write
};
 
void storeMEM(){
  //Write each frequency section to a EPROM slot.  Yes, it's cheating but it works!
   EEPROM.write(0,millions);
   EEPROM.write(1,hundredthousands);
   EEPROM.write(2,tenthousands);
   EEPROM.write(3,thousands);
   EEPROM.write(4,hundreds);       
   EEPROM.write(5,tens);
   EEPROM.write(6,ones);   
   memstatus = 1;  // Let program know memory has been written
   Serial.println(rx);
};
 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165

4、实物验证