systemverilog：interface中端口方向、Clocking block的理解

（1）从testbench的角度看，tb中信号的输入输出方向与interface中信号输入输出方向一致：
（2）从DUT角度看，DUT中信号输入输出方向与interface中信号输入输出方向相反。简单图示如下：

代码示例如下：
 

interface my_if(input bit clk);
	bit write;
	bit [15:0] data_in;
	bit [7:0] address;
	logic [15:0] data_out;
 
	clocking cb @ (negedge clk);
		default input #1ns output #2ns;
		output  write;
		output  data_in;
		output   address;
		input data_out;
	endclocking
 
	modport master(clocking cb);
 
	modport slave(input write, data_in, address, output data_out);
 
endinterface
 
module master( clk,data_out  ,  write ,data_in,address );
	input logic clk,write;
	output logic [7:0] data_out;
	input logic [7:0] data_in ,address;
	
	
	always @(negedge clk)
		if(write==0)
			data_out<=0;
		else if (write==1)
			data_out<=data_in;
			
endmodule
 
 
class BB;
 
 virtual  my_if master_inst;
 
function new(virtual interface  my_if a);
	master_inst=a;
endfunction
	
task ass();
	master_inst.master.cb.write<=0;
	repeat(10) @(posedge master_inst.clk);
		master_inst.master.cb.data_in<='h12;
	repeat(10) @(posedge master_inst.clk);
		master_inst.master.cb.data_in<='h34;	
 
	repeat(10) @(posedge master_inst.clk);
		master_inst.master.cb.data_in<='h45;
master_inst.master.cb.write<=1;
	repeat(10) @(posedge master_inst.clk);
		master_inst.master.cb.data_in<='h56;	
 
	repeat(10) @(posedge master_inst.clk);
		master_inst.master.cb.data_in<='h67;
	repeat(10) @(posedge master_inst.clk);
		master_inst.master.cb.data_in<='h52;	
 
	repeat(10) @(posedge master_inst.clk);
		master_inst.master.cb.data_in<='h81;
	repeat(10) @(posedge master_inst.clk);
		master_inst.master.cb.data_in<='h05;	
		
endtask
 
endclass
 
 
module slaver(my_if.slave sif);
	
	initial begin
		sif.data_out <= 16'h0;
		#275 sif.data_out <= 16'h1;
	end
endmodule
 
module test;
	bit clk = 0;
 
	always #50 clk = ~clk;
 
	my_if regbus(clk);
	
	master m0(.clk(regbus.clk ), .address(regbus.address), .data_out(regbus.data_out), .data_in(regbus.data_in),.write(regbus.write));
	
	//slaver s0(regbus.slave);
	
	 BB b_inst=new(regbus);
	 
	initial begin
	 
	 #100 b_inst.ass();
	 
	end
 
endmodule 
 
 

注意：
（1）当interface中有modport或者clocking块时，在testbench中可以直接定义interface的实例，可以将其直接传递到class中，然后在class中的task中可以通过点运算法逐层次的访问modport或者clocking中的信号。也可以通过点运算符直接在tb中实例化interface中的modport对象，然后传递到class中。
（2）在class中的task中对clocking块中的信号赋值时，必须使用非阻塞赋值语句<=;