EagleSDR USB HAT FT600

给EagleSDR做了个USB 3.0的子卡，采用FT600方案，实物如下：

用FT600DataStreamerDemoApp测试，速度如下：

由于FT600是16bit的接口，如果用FT601的32bit接口，性能应该还会有大幅提升。
测试代码很简单，参考了网上大佬的例程

`timescale 1ns / 1ns

module FT600_stream
(
    //PL时钟
    input                  pl_clk,          //PL端时钟
    // 复位
    input                  rst_n,           //外部复位
    output reg             ft600_reset_n,   //ft600复位

    // FIFO interface    
    input                  ft600_clk,
    inout [15:0]           ft600_data,
    inout [1:0]            ft600_be,
    input                  ft600_rxf_n,
    input                  ft600_txe_n,
    output                 ft600_oe_n,
    output                 ft600_wr_n,
    output                 ft600_rd_n
);

reg ft600_wakeup_reg;

//从host来，退出读操作
wire r_oob;
//从host来，退出写操作
wire w_oob;

// assign ft600_siwu_n = 1'b1;             // pull-up

wire [15:0] rd_data;
wire [15:0] wr_data;
wire [1:0] be_rd;
reg [1:0] be_wr;
reg [2:0] ft600_state;                  //状态

localparam  FT600_IDLE=0,
            FT600_READ=1,
            FT600_READ_ABORT=2,
            FT600_WRITE=3,
            FT600_WRITE_ABORT=4;

assign rd_data  =  ft600_data;
assign ft600_data  =  (ft600_state==FT600_WRITE || ft600_state==FT600_WRITE_ABORT) ? wr_data : 16'bz;
assign be_rd    =   ft600_be;
assign ft600_be =  (ft600_state==FT600_WRITE || ft600_state==FT600_WRITE_ABORT) ? be_wr : 2'bz;// write data dir


reg [15:0] wr_cnt;
assign wr_data = 16'hffff - wr_cnt;

//写计数器
always @(posedge ft600_clk)
begin
    if(!ft600_reset_n)begin
        wr_cnt <= 16'd0;
    end
    else 
    if(!ft600_wr_n) 
    begin
        wr_cnt <= wr_cnt + 1'b1;
    end
end

//写信号
assign ft600_wr_n=!((ft600_state==FT600_WRITE || ft600_state==FT600_WRITE_ABORT) && !ft600_txe_n);
//读信号，读状态且有数据可读
assign ft600_rd_n=!((ft600_state==FT600_READ || ft600_state==FT600_READ_ABORT) && (!ft600_rxf_n));
//在空闲态或读状态，且有数据可读时，允许FT600控制数据线
assign ft600_oe_n=!((ft600_state==FT600_IDLE || ft600_state==FT600_READ || ft600_state==FT600_READ_ABORT) && !ft600_rxf_n);

//定时器
localparam DELAY_5MS_CNT=(5*100000-1);
reg[31:0] delay_timer;

//状态机
always @(posedge ft600_clk)begin
    if(!ft600_reset_n)
    begin
        ft600_state <= FT600_IDLE;
    end
    else 
    begin
        if (r_oob)
        begin
            be_wr<=2'b01;
            delay_timer <= DELAY_5MS_CNT;
            ft600_state<=FT600_WRITE_ABORT;
        end
        else if (w_oob)
        begin
            delay_timer <= DELAY_5MS_CNT;
            ft600_state<=FT600_READ_ABORT;
        end
        else
        begin
            case(ft600_state)
            FT600_IDLE:
            begin
                be_wr <= 2'b11;
                if((!ft600_rxf_n))
                    ft600_state  <= FT600_READ;         //有数据可读
                else if(!ft600_txe_n)
                    ft600_state  <= FT600_WRITE;        //可写入数据
                else
                    ft600_state <= FT600_IDLE;
            end
            FT600_READ:
                if (ft600_rxf_n)
                    ft600_state  <= FT600_IDLE;
            FT600_READ_ABORT:
                if (delay_timer==32'b0)
                    ft600_state <= FT600_IDLE;
                else
                begin
                    delay_timer=delay_timer-1'b1;
                end
            FT600_WRITE:
                if(ft600_txe_n)
                    ft600_state  <= FT600_IDLE;
            FT600_WRITE_ABORT:
                if (delay_timer==32'b0)
                    ft600_state <= FT600_IDLE;
                else
                begin
                    delay_timer=delay_timer-1'b1;
                end
            endcase
        end           
    end
end

//延时复位
localparam RST_CYCLE=100;
reg [19:0] rst_cnt;

always @(posedge pl_clk)
begin
    if (!rst_n)
    begin
        ft600_reset_n<=0;
        rst_cnt<=0;
    end
    else
    begin
        if (rst_cnt<RST_CYCLE)
            rst_cnt<=rst_cnt+1;
        else
        begin
            ft600_reset_n<=1;
        end
    end
end

endmodule
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155